Skip to content
MedCareerPrep
Open app
☰

CRCST Manual and Mechanical Cleaning: study notes and practice questions

Part of the CRCST Cleaning, Decontamination and Disinfection domain, 21% of the exam. This topic covers why cleaning comes first, point-of-use care, manual cleaning at the sink, detergents and how to dilute them, ultrasonic cleaners, washer-disinfectors and cart washers, rinse water, and single-use and loaner devices. For most questions the deciding fact is the device or detergent manufacturer's instructions (IFU).

Study notes ↓Chapter quiz ↓All free questions ↓

All chapters

CRCST Manual and Mechanical Cleaning study notes

This topic covers why cleaning comes first, point-of-use care, manual cleaning at the sink, detergents and how to dilute them, ultrasonic cleaners, washer-disinfectors and cart washers, rinse water, and single-use and loaner devices. For most questions the deciding fact is the device or detergent manufacturer's instructions (IFU).

Why cleaning comes first

  • Soil left on a device, organic or inorganic, acts as a shield between microbes and the disinfectant or sterilant.
  • A dirty device cannot be reliably disinfected or sterilized; a longer sterilizer cycle does not make up for it.
  • Start cleaning as soon as practical after use, because dried or baked-on soil is harder to remove and can make disinfection or sterilization fail.
  • Every used item that arrives in decontamination is treated as contaminated, so PPE is worn to handle it.
  • After cleaning, every instrument is still inspected and must be visibly clean.

Point of use and receiving

  • Point-of-use care does not replace cleaning; it is the first step of cleaning.
  • Keep soiled instruments open and moist with an enzymatic spray, a towel wet with water, or a foam or gel made for this purpose.
  • Do not use saline to keep instruments moist or to soak them; saline (like dried blood) can damage stainless steel and other devices.
  • A loaner set from a vendor enters the same cycle as the facility's own devices: clean, inspect, package and sterilize it per the IFU, whatever another site says it did.

Manual cleaning at the sink

  • Take devices with removable parts apart as far as the IFU allows, and keep all the parts together so they can be reassembled.
  • CDC names two essentials of manual cleaning: friction (scrubbing with a brush or cloth) and fluidics (fluid under pressure to flush channels).
  • Fully submerge immersible items and scrub them below the water surface so aerosols do not form.
  • Do not scrub under running water or above the water line; both spray contaminated droplets.
  • Use soft nylon brushes; metal brushes and abrasives scratch instruments.
  • A lumen brush should match the lumen's diameter so the bristles touch the walls, and be long enough to come out the far end.
  • Reusable brushes must be cleaned and then sterilized or high-level disinfected between uses, unless disposable brushes are used.

Detergents, enzymes and dilution

  • Neutral or near-neutral pH detergents are most gentle on device materials and still remove soil well.
  • Enzymatic cleaners usually contain proteases that break down proteins such as blood and pus; some add lipases for fat and amylases for starch.
  • Enzymatic cleaners are not disinfectants: they kill nothing, so items stay contaminated.
  • Because they do not stop microbes growing, discard enzymatic solutions after each use, for example after each endoscope.
  • Rinse enzymes off devices; residue can cause reactions such as fever.
  • Per CDC, a neutral pH detergent with enzymes is the best choice for delicate instruments, especially flexible endoscopes; alkaline cleaners dissolve protein and fat well but can corrode.
  • Household dish or laundry detergents are not suitable for medical devices.
  • Dilution, water temperature and contact time come from the detergent label; some products are designed for a specific temperature.
  • A stronger mix is not necessarily more effective, and water that is too hot sets protein: WHO says protein coagulates above 60°C (140°F).

Example

The label calls for a 1% solution. The sink holds 10 liters and the detergent comes full strength (100%). How much detergent goes in?

Solution

Detergent volume = concentration needed × sink volume in mL ÷ supplied concentration = 1 × 10,000 ÷ 100 = 100 mL. Add 100 mL and fill to 10 liters. Check: 10 mL would be 0.1% (too weak) and 1,000 mL would be 10% (too strong).

Ultrasonic cleaners

  • Sound waves pass through the solution and form bubbles that grow, become unstable and implode; this cavitation pulls soil out of box locks, serrations, hinges and lumens.
  • Remove gross soil first, open the instruments, submerge them fully and fill the lumens.
  • Degas the unit every time it is filled: fill it, close the lid and run a cycle for 5 to 10 minutes, because dissolved gas weakens cavitation.
  • Change the solution daily and whenever it is visibly dirty; used solution can hold bacteria and endotoxin.
  • Close the lid before running a cycle, then rinse and dry the instruments afterward.
  • Check each device's IFU first; some powered or lensed devices must not go in an ultrasonic cleaner, and fitting in the basket does not make them safe.

Washer-disinfectors and cart washers

  • Washer-disinfectors clean by impingement: pressurized water sprays the soil off, helped by detergent and heat.
  • WHO's typical cycle: pre-rinse, enzymatic wash, detergent wash, lubrication, then a final rinse hot enough to disinfect, ideally with deionized water to prevent spotting.
  • Open hinged instruments fully, take items apart as far as possible, and never stack instruments or trays.
  • Do not overload racks; place multi-level trays separately and remove all lids.
  • Inspect the spray arms daily and keep them clear.
  • A commercial test soil that mimics dried blood can check the washer; a failure points to a machine fault or a chemical not feeding in, but a pass does not prove instruments are clean.
  • Check and document each cycle's parameters.
  • Cart washers clean carts, rigid containers and basins; their cycle lacks the enzymatic wash and lubrication, so instruments go in only if the equipment maker has validated it.

Rinse water and TASS

  • Rinse after cleaning to remove loosened soil and detergent, which could react with the disinfectant or sterilant.
  • WHO: give lumens of intravascular or intrathecal devices a final rinse with sterile, pyrogen-free water or reverse osmosis water; distilled water may still carry microbes or pyrogens.
  • Toxic anterior segment syndrome (TASS) is acute, noninfectious inflammation of the front of the eye, usually within 24 hours of surgery such as cataract removal.
  • Most TASS cases trace to contaminants on instruments from poor cleaning, or to substances that enter the eye during surgery.
  • In a 2006 Maine cluster, changes included rinsing with sterile distilled water instead of tap water after the ultrasonic bath, changing the bath twice daily instead of once, and stopping the enzymatic cleaner in the bath.

Single-use devices

  • A single-use device is meant for one use, or one patient during one procedure, and then discarded.
  • Single-patient use is a different label; single-use items are not cleaned and reused just because they look clean.
  • FDA holds a hospital or third party that reprocesses single-use devices to the same rules as the original manufacturer: premarket clearance, registration and listing, adverse event reporting, tracking, recalls and labeling.

Key terms

Point-of-use treatment
Keeping used instruments open and moist right after the procedure; it starts but never replaces cleaning.
Friction
Rubbing or scrubbing soil off with a brush or cloth; one of two essentials of manual cleaning.
Fluidics
Fluid forced under pressure through channels to flush out soil, especially where a brush cannot pass.
Enzymatic cleaner
Detergent with proteases (and sometimes lipases or amylases) that digests soil but kills no microbes.
Neutral pH detergent
Cleaning solution that is neither acidic nor alkaline; with enzymes it is CDC's preferred choice for delicate instruments and flexible endoscopes.
Alkaline cleaner
High-pH detergent that dissolves protein and fat efficiently but can corrode devices.
Cavitation
Formation and implosion of tiny bubbles from sound waves, which pulls debris off instruments in an ultrasonic unit.
Degassing
Running a freshly filled ultrasonic unit with the lid closed for 5 to 10 minutes to remove dissolved gas.
Impingement
Pressurized water spray that physically knocks soil off; the main cleaning action of a washer-disinfector.
Thermal rinse
Final hot-water step of a washer-disinfector cycle that disinfects by heat.
Test soil
Commercial product mimicking dried blood, used to check that a washer-disinfector is cleaning properly.
Cart washer
Machine for carts, rigid containers and basins; lacks enzymatic wash and lubrication steps.
Pyrogen-free water
Water free of fever-causing substances such as endotoxin; required for final rinsing of intravascular device lumens.
TASS
Toxic anterior segment syndrome: acute, noninfectious eye inflammation after anterior segment surgery, often from instrument residue.
Single-use device
Item intended for one use or one patient in one procedure, then discarded.
Instructions for use (IFU)
Manufacturer's written directions for reprocessing a device or using a chemical; they set disassembly, dilution, temperature and method.

Common mistakes

  • Point-of-use wiping or spraying does not disinfect and does not replace cleaning, and saline is never used to keep instruments moist.
  • Do not scrub under running water or above the water line; scrub immersible items below the surface. Lumen brushes must match the lumen diameter, not be the smallest or a forced oversize.
  • Enzymatic cleaners are not disinfectants, must be measured and rinsed off, and are discarded after each use. More detergent, hotter water or a stronger mix is not better; follow the label.
  • Cavitation is the ultrasonic cleaner; impingement is the washer-disinfector. Degas after every fill and change cloudy solution now, not at the end of the shift.
  • In washers, keep hinged instruments open, do not stack or overload, and remove lids. A failed test soil means a washer or chemical-feed problem, not a sterility result, and a cart washer is not used for instruments unless validated.
  • Distilled water may still contain microbes or pyrogens. A loaner marked 'processed' elsewhere still gets full reprocessing, and a hospital that reprocesses single-use devices is treated by FDA as a manufacturer.

Checked against: CDC, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated 2024), print version; WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016); CDC MMWR, Toxic Anterior Segment Syndrome After Cataract Surgery, Maine, 2006; FDA, Reprocessing of Single-Use Devices (archived page)

Chapter quiz

6 questions from this chapter, with an explanation after each answer.

1/6

Manual and Mechanical Cleaning

Which tool should be used to scrub the serrations and box locks of stainless steel instruments?

Manual and Mechanical Cleaning questions and answers

Read each question, choose your answer, then open the explanation.

  1. 1.Which tool should be used to scrub the serrations and box locks of stainless steel instruments?

    • A.A soft nylon-bristle brush
    • B.A stainless steel wire brush
    • C.A steel wool scouring pad
    • D.Any brush at all, as long as it is used under running water
    Show answer

    Answer: A. A soft nylon-bristle brush

    WHO advises soft nylon-bristle brushes so the instrument surface is not damaged. Metal brushes and abrasive items should never be used on instruments.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)

  2. 2.Stainless steel instruments come out of the washer-disinfector with a white-gray film. What is the most likely cause?

    • A.Hard water minerals such as calcium and magnesium
    • B.Too little lubricant added during the final rinse
    • C.Blood proteins left behind by a short pre-rinse
    • D.A thermal rinse run at too low a temperature
    Show answer

    Answer: A. Hard water minerals such as calcium and magnesium

    WHO notes that hard water leaves a white-gray residue on instruments after drying. Its calcium and magnesium also make cleaning chemicals less effective and can damage instruments over time.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)

  3. 3.Why must instruments be thoroughly cleaned before sterilization?

    • A.Cleaning is needed only so the instruments look acceptable to the surgeon
    • B.Sterilant works better when it mixes with leftover blood and tissue
    • C.Leftover organic and inorganic soil shields microbes from the sterilant
    • D.Cleaning can be skipped if the sterilizer exposure time is doubled
    Show answer

    Answer: C. Leftover organic and inorganic soil shields microbes from the sterilant

    CDC explains that organic and inorganic material left on instruments interferes with high-level disinfection and sterilization by acting as a barrier to the sterilizing agent. Cleaning also lowers the bioburden.

    Checked against CDC, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated 2024), print version

  4. 4.Why should cleaning of used instruments begin as soon as practical after use?

    • A.Instruments stay under warranty only if cleaned within one hour of use
    • B.Fresh blood is sterile, so early cleaning avoids contaminating the room
    • C.Soil that dries or bakes on is harder to remove and can defeat sterilization
    • D.Early cleaning lets the department skip inspection before packaging
    Show answer

    Answer: C. Soil that dries or bakes on is harder to remove and can defeat sterilization

    CDC recommends cleaning devices as soon as practical after use, because soil that dries or bakes onto instruments is harder to remove and can make disinfection or sterilization less effective or even ineffective.

    Checked against CDC, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated 2024), print version

  5. 5.An instrument has several removable parts. How should it be prepared for cleaning?

    • A.Leave it assembled so small parts are not lost in the washer
    • B.Take it apart as far as the IFU allows, keeping the parts together
    • C.Remove only the parts that look visibly soiled
    • D.Take it apart and send the small parts to a separate cart for reuse
    Show answer

    Answer: B. Take it apart as far as the IFU allows, keeping the parts together

    CDC states that items with more than one removable part should be disassembled, taking care to keep all parts together so reassembly is efficient. The device IFU defines how far to disassemble.

    Checked against CDC, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated 2024), print version

  6. 6.When manually cleaning an immersible instrument at the sink, where should the technician scrub it?

    • A.Under a running faucet, so loosened soil is rinsed straight away
    • B.Below the surface of the water, to keep aerosols from forming
    • C.Above the water line, so the technician can see the soil clearly
    • D.On a dry towel beside the sink, then dip it in water to rinse
    Show answer

    Answer: B. Below the surface of the water, to keep aerosols from forming

    WHO instructs that immersible devices be fully submerged and scrubbed beneath the water line so no aerosols form, and warns against cleaning under running water.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)

  7. 7.What size brush should be used to clean the lumen of a cannulated instrument?

    • A.One the same diameter as the lumen and long enough to exit the far end
    • B.The smallest brush available, so it slides through without resistance
    • C.A brush slightly wider than the lumen, forced in to scrub harder
    • D.Any brush on hand, since the washer will finish cleaning the lumen
    Show answer

    Answer: A. One the same diameter as the lumen and long enough to exit the far end

    WHO states that lumen brushes must be the same diameter as the instrument so all internal surfaces are reached, and long enough to exit the distal end. CDC similarly says bristles should contact surfaces.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)

  8. 8.Which statement about enzymatic cleaners is correct?

    • A.They are disinfectants that make instruments safe to handle without gloves
    • B.They work the same at any dilution, so measuring is not necessary
    • C.They never need rinsing, because enzymes evaporate during drying
    • D.They break down proteins such as blood but do not kill microorganisms
    Show answer

    Answer: D. They break down proteins such as blood but do not kill microorganisms

    CDC states enzymatic cleaners (usually proteases) attack proteins in soil such as blood and pus, but they are not disinfectants. They must be diluted as directed and rinsed from equipment.

    Checked against CDC, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated 2024), print version

  9. 9.How does an ultrasonic cleaner remove soil from instruments?

    • A.Cavitation: tiny bubbles form and implode, pulling soil off surfaces
    • B.High-pressure jets of water strike the instruments from rotating arms
    • C.Steam under pressure loosens soil and kills microorganisms
    • D.Abrasive particles in the solution scrub the instrument surfaces
    Show answer

    Answer: A. Cavitation: tiny bubbles form and implode, pulling soil off surfaces

    Ultrasonic cleaners send sound waves through the solution, creating bubbles that become unstable and implode (cavitation), drawing debris out of box locks, serrations, hinges and lumens.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)

  10. 10.Washer-disinfectors remove soil mainly by which principle?

    • A.Cavitation, using sound waves in a water bath
    • B.Impingement, using pressurized water spray
    • C.Oxidation, using hydrogen peroxide vapor
    • D.Alkylation, using a liquid chemical sterilant
    Show answer

    Answer: B. Impingement, using pressurized water spray

    WHO explains that washer-disinfectors work by impingement, using pressurized water to physically remove bioburden, combined with detergents and a thermal rinse.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)

  11. 11.What does it mean when a device is labeled single-use by its manufacturer?

    • A.It may be reused on the same patient for up to one week
    • B.It may be reprocessed once, then discarded after the second use
    • C.It is intended for one patient during one procedure and then discarded
    • D.It may be reused if it passes visual inspection after cleaning
    Show answer

    Answer: C. It is intended for one patient during one procedure and then discarded

    WHO defines a single-use device as one meant to be used just once, or on one patient during one procedure, and then thrown away. FDA treats anyone who reprocesses such a device as its manufacturer.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)

  12. 12.Point-of-use treatment of instruments in the operating room accomplishes which of the following?

    • A.It replaces cleaning in decontamination when the instruments look clean
    • B.It disinfects the instruments, so decontamination staff can handle them without PPE
    • C.It is only needed for instruments that will be high-level disinfected
    • D.It starts the cleaning process but does not replace full cleaning later
    Show answer

    Answer: D. It starts the cleaning process but does not replace full cleaning later

    WHO says point-of-use preparation is the first stage of cleaning and does not take the place of full cleaning in decontamination. It keeps soil from drying and helps protect instruments.

    Checked against WHO/PAHO, Decontamination and Reprocessing of Medical Devices for Health-care Facilities (2016)